This is a COMPLETE Transmission, No Need to send us a Core T56! Price Includes FREE Shipping!

Introduced to the marketplace in 2012, the Magnum XL is a continuation of the popular Magnum 6-speed series. Featuring all the most important content from the original Magnum, the XL retains its brute strength and sophistication, but eliminates its multiple shifter locations and dual speedo outputs. Refinements include a new extended length tail section designed to eliminate the semi-remote shifter found in many popular late-model applications. Initially available for the 2005 and up “S197” Mustang, the Magnum XL was designed specifically to replace the OEM 5 or 6 speed transmission where performance improvements are desired. Simplifying the swap, the FORD Magnum XL includes a SFI-approved steel bellhousing, cross member, trans mount, isolated shifter, and shift ball. It also reuses the OEM hydraulic clutch release system.

. Some benefits you'll enjoy over a standard T56 transmission include:

The ability to choose between 2.66 and 2.97 gearsets
Triple-cone synchronizers on 1-4 gears, along with double-cone synchronizers on Fifth, Sixth and Reverse
Wider, two-piece laser beam-welded speed gears which feature built-in positive stops to virtually eliminate the possibility of "overthrown" shifts
Much stronger one-piece countershaft that resists distortion far better than previous designs and uses larger bearings in all critical support areas for increased stability
Input Shaft features additional material throughout the length of the shaft, increased face width, a larger input bearing, and generously long splines to accommodate twin-disc clutch setups
Considerably narrower synchronizers that feature fine-pitch tooth angles to effectively decrease the amount of travel necessary for engagement
Redesigned shift forks featuring integrated "shift keys" to virtually eliminate the possibility of bending shift forks
Added cross-sectional material on shift forks for increased rigidity and larger shift pads to promote better wear characteristics

When you place your order, we completely tear down the T56 Magnum and begin our upgrades that we perform in house. Those upgrades include:

Installing Carbon Blocker Rings on first, third and fourth gears (second gear is already carbon)
Upgrading all fork pads from plastic to bronze
End-play set to our custom specifications
Professional Reassembly done 100% by hand
5 Qts of Fluid

We also provide you with a new vehicle speed sensor, reverse lockout solenoid and reverse light switch.

Option Guide: Which 1-6 Gear Ratio Set do I need?
It truly depends on how you plan to use the car! The 2.66 Gear Ratio set retains the same 1-4 gears as the Stock LS1 F-Body T56 but has slightly more aggressive overdrive gears. The 2.97 Gear Ratio set retains the same overdrive gears as the Stock LS1 F-Body T56 but has slightly more aggressive 1-4 gears. If traction is something you're constantly trying to find, the 2.66 Gear Set will be a bit more forgiving.

Option Guide: Billet Front Plate

Include the Tick Performance Billet Front plate and save $200. The sprayer consisted of a machined and welded bar that extrudes into the transmission, coating 2nd, 3rd, and 4th gears more evenly with oil.

· Improved Bungs and Sprayer system coats 2nd, 3rd and 4th gears in oil

· Improved rigidity, better gear mesh, and engagement

· O-ring sealing for a leak-proof design

· Can be used with either T56 or Magnums (includes necessary adapters)

The Tick Performance Billet Front Plate for T56 and T56 Magnums is machined here in house in Mount Airy, North Carolina. The billet design vastly improves strength, which decreases gear deflection and enhances performance.

In our testing, we’ve found better gear engagement and improved gear wear patterns. It handles torque deflection better, too, improving the life of your transmission. See the dropdown menu to add it to your build. T56 transmissions require an additional bearing ($39.99). The billet plate pricing includes the Tick Performance Hi-Flow Trans Pump kit (with filter and fittings).

Option Guide: Should I have the Bungs & Sprayers Installed?
It is seen time and time again in big horsepower cars that do standing mile or high speed pulls often, and road race or autocross applications; the input shaft bearing can become starved for fluid and fail, causing a chain reaction of damage inside the transmission. With this option, we install and weld bungs and spray tubes inside your transmission that will direct transmission fluid onto your input shaft and third gear teeth that are prone to failure. This kit now includes our Hi-Flow Transmission Fluid Pump Kit. This kit will require some plumbing and electrical wiring. This option adds no extra turnaround time.

Option Guide: Should I Upgrade to an Aftermarket Gear Set?
Tick Performance has partnered with PPG to offer the strongest gear sets on the market with our industry leading transmissions. You have the following options for gear sets:

Faceplated 1st-6th
Faceplated 1st-4th (Allows you to retain or delete your 5th & 6th gear)
Synchronized 1st-6th
Synchronized 1st-4th (Allows you to retain your OEM 5th & 6th gear)

Faceplated gear sets are designed for race only applications and not recommended for street use. The faceplated gear sets include the gears, mainshaft, billet shift forks, slider assemblies, and billet interlock & bolts. The synchronized gear sets include only the gears themselves and will reuse the factory synchronizer assemblies, shift forks, mainshaft, and interlock.

The synchronized gear sets are available with the following ratio:

2.437 – 1.611 – 1.228 – 1.000 - .891 - .80.

2.437 – 1.611 – 1.228 – 1.000 - .797 - .634.

The faceplated gear sets are available in the following ratios:
2.148 - 1.561 - 1.228 - 1.000 - .875 - .770
2.437 - 1.611 - 1.228 - 1.000 - .875 - .770
2.589 - 1.841 - 1.352 - 1.000 - .797 - .630
2.946 - 2.071 - 1.438 - 1.000 - .797 - .630

If you are planning to retain your factory 5th & 6th gear the ratio will change as the PPG input ratio is different than OEM. To find your new ratio please use the following formula.

OEM Ratio / 1.161 = Y
Y x 1.381 = New Ratio

Option Guide: Do I want Powdercoating?
This transmission will look brand new when it arrives at you door, but if you're building a show car you may opt for powdercoating, which is much more durable than paint. Available in Black Satin or Silver. This option adds 10-15 days to your turnaround time. NOTE The inlet port for the slave cylinder feed line may need to be clearanced to allow proper seating of the slave cylinder.

***UPDATED 08/09/2022*** Tick Performance warrants that each transmission sold by Tick Performance will be free from defects in material and workmanship under normal use for a period of 90 days after delivery of the transmission. Tick Performances sole obligation under this warranty shall be to repair or replace, at its option, the defective transmission at no charge to the customer. Under no circumstance will Tick Performance be liable for any oil, towing, labor, or rental vehicle charges. As a condition of this warranty the customer must return any allegedly defective product, freight prepaid to Tick Performance, accompanied by a packing slip indicating the shipper and a copy of the original invoice. This warranty does not apply to unsatisfactory product performance which is attributed in whole or in part, to any factor, condition, or circumstance other than defects in material or workmanship. Without limiting the foregoing, this warranty shall be null and void if repair or replacement is required because of improper installation, accident, physical or electrical stress, neglect, misuse, or any other cause other than the ordinary and intended use for which the product was designed, or if the product has been dismantled, altered, or repaired by the customer or by any third party. This warranty expressly does not cover loss or injury from the use of the product. By accepting and/or installing product, you are agreeing to the terms of the warranty. Parts damaged due to any reason other than defects in material or workmanship will be the sole responsibility of the customer. We are selling you an incomplete product. Life and performance of transmissions are dictated by quality of installation, associated components, and capability of the driver/operator. It is the potential installer and/or assembler’s responsibility to determine whether he or she has the necessary skills, knowledge, and tools to properly and safely install the Tick Performance built transmission described herein. Improper installation may cause the vehicle to function improperly or not to function. Improper assembly and/or installation may additionally cause a risk to personal safety or property. If the assembler and/or installer is confused or has questions or concerns about a particular assembly or installation, he or she should contact Tick Performance before proceeding further. The information contained in these instructions does not constitute a warranty or guarantee of any kind. An assembler’s and/or installer’s failure to correctly follow these guidelines constitutes a waiver of the assembler and/or installer’s rights against Tick Performance regarding any subsequent damages to property or personal injury caused by the assembler’s and/or installer’s improper assembly and/or installation. Tick Performance is not responsible for any vehicle damage resulting from improper installation or transmission failure. It is the customer and/or installers responsibility to install proper safety equipment into the vehicle upon installation of transmission or components. If you feel the need to act upon this warranty, you must contact Tick Performance at the first sign of an issue via phone and email. If contact is not made when the issue arises, and normal operation of the vehicle continues the warranty will be void.